0,"Error - Unknown",255,0,0
1,"File Not Found - ",255,0,0
2,"Error - Line Too Long",255,0,0
3,"Error - Syntax - Command or File Not Found",255,0,0
4,"Error - Arc Radius",255,0,0
5,"Error - Unsupported G Code",255,0,0
6,"Error - Unsupported L Code",255,0,0
7,"Error - Unsupported M Code",255,0,0
8,"Error - Soft Limit Exceeded",255,0,0
9,"Error - Multiple Commands",255,0,0
10,"Error - Demo Count Exceeded",255,0,0
11,"Error - Acceleration Out of Bounds",255,0,0
12,"Error - Arc Too Small",255,0,0
13,"Error - ZW Exceeds XY in Helix",255,0,0
14,"Error - Helical Interpolation Not Supported",255,0,0
15,"Error - Illegal Value",255,0,0
16,"Error - Unknown Position Specified",255,0,0
17,"Error - Subprogram Nesting Too Deep",255,0,0
18,"Error - L10 in Subprogram",255,0,0
19,"Error - Unknown",255,0,0
20,"Error - Multi Axis Helical Not Supported",255,0,0
21,"Error - Boundary Exceeded",255,0,0
22,"Error - Auto Rotation XYZ Not Supported",255,0,0
23,"Error - Parameter Not Specified",255,0,0
24,"Error - Not a BMP File",255,0,0
25,"Error - Unknown",255,0,0
26,"Error - BMP File Invalid Header",255,0,0
27,"Error - Memory Error",255,0,0
28,"Error - 2-Bit Bitmap Engrave Not Enabled",255,0,0
29,"Error - Invalid L10 Command",255,0,0
30,"Error - Invalid P1 Command",255,0,0
31,"Error - Command Not Implemented",255,0,0
32,"Error - Tool Changer Not Enabled",255,0,0
33,"Error - Parameter Out Of Range",255,0,0
34,"Error - Device Not Enabled",255,0,0
35,"Error - Could Not Open File",255,0,0
36,"Error - Pump Control Not Enabled",255,0,0
37,"Error - 8-Bit Bitmap Engrave Not Enabled",255,0,0
38,"Error - Soft Limits Not Enabled",255,0,0
39,"Error - Tangential Knife Not Enabled",255,0,0
40,"Error - Forced Limit Exceeded",255,0,0
41,"Error - Digitizer Probe Not Enabled",255,0,0
42,"Error - Vector Laser Not Enabled",255,0,0
43,"Error - Arcs Disabled When X or Y Scaled",255,0,0
44,"Error - Rotating Saw Not Enabled",255,0,0
45,"Error - D/A Not Enabled",255,0,0
46,"Error - Macro Expansion Error",255,0,0
47,"Error - Auto-AuxOut Not Enabled",255,0,0
48,"Error - Depth Must Be Lower Than Retract",255,0,0
49,"Error - SST Drive Control Not Enabled",255,0,0
50,"Error - SST Drive Communications Failed",255,0,0
51,"Error - Cutter Comp. Buffer Full",255,0,0
52,"Error - Cutter Comp. Intersection Error",255,0,0
53,"Error - Wrong Position For Current Gantry Map Increment",255,0,0
54,"Error - Gantry Mapping Not Enabled",255,0,0
55,"Error - Laser Scanner Not Ready",255,0,0
56,"Error - Laser Scanner Not Enabled",255,0,0
57,"Error - Laser Scanner Error",255,0,0
58,"Error - L82.1 Not Set",255,0,0
59,"Error - Probe Error",255,0,0
60,"Error - G28 Required for ",255,0,0
61,"Error - Probe Radius Compensation Failed.",255,0,0
501,"4th Axis is Used/Laser Disabled",255,0,0
502,"6th Axis is Used/Laser Disabled",255,0,0
503,"Specified Axis is Used/Laser Scanner Disabled",255,0,0
504,"Number of Axis Specified Exceeds Maximum",255,0,0
505,"At Least Two Axis Required/Laser Scanner Disabled",255,0,0
506,"Maximum velocity decreased for ",255,0,0
507,"Can't Load PCI 48H Card/using PCI DIO 24H Card",255,0,0
508,"Can't Find PCI DIO 48H Card",255,0,0
509,"Error in PCI DIO 48H Setup",255,0,0
510,"Can't Load PCI 24H Card/using PCI DIO 48H Card",255,0,0
511,"Can't Find PCI DIO 24H Card",255,0,0
512,"Error in PCI DIO 24H Setup",255,0,0
513,"Upgrade Required For IJoist",255,0,0
514,"Upgrade Required For Tangential Knife",255,0,0
515,"Upgrade Required For Com DLL",255,0,0
516,"AD Device Initialization Failed",255,0,0
517,"Laser Probe Initialization Failed",255,0,0
518,"SST Device Initialization Failed",255,0,0
519,"Simulating - ",0,0,255
520,"Viewing - ",0,0,255
521,"Simulation Completed",0,0,255
522,"Error During Simulation",255,0,0
523,"Finished: ",0,0,255
524,"Elapsed Time: ",0,0,255
525,"File Has Been Restarted",255,0,0
526,"Restart Passed End of File",255,0,0
527,"Aborted - ",255,0,0
528,"Aborted - Limit Switch Low ",255,0,0
529,"Aborted - Limit Switch High ",255,0,0
530,"Aborted - Limit Switch ",255,0,0
531,"Aborted - Digitizer Probe",255,0,0
532,"Aborted - Aborted By User",255,0,0
533,"Aborted - Soft Limit Low ",255,0,0
534,"Aborted - Soft Limit High ",255,0,0
535,"Aborted - Boundary Low ",255,0,0
536,"Aborted - Boundary High ",255,0,0
537,"Line - ",255,0,0
538,"Could not import DXF file",255,0,0
539,"Could not import HPGL file",255,0,0
540,"Laser Scan - Creating Output File",0,0,255
541,"Laser Scan - Output File Created",0,0,255
542,"Laser Scan - Error Creating Output File",255,0,0
543,"Error - Could Not Open Scan Data File",255,0,0
544,"Creating SCAN.STL",0,0,255
545,"Could Not Create Digitized Data File",255,0,0
546,"Digitized File Started",0,0,255
547,"Nothing to Undo",255,0,0
548,"Undo Successful",0,0,255
549,"Undo Failed",255,0,0
550,"No Files Open",255,0,0
551,"Shape Closed",0,0,255
552,"File Not Opened",255,0,0
553,"No Data To Save",255,0,0
554,"File Saved",0,0,255
555,"Exited Manual Digitizer",0,0,255
556,"Error Saving File",255,0,0
557,"Rapid Move Added",0,0,255
558,"Must complete arc first",255,0,0
559,"Feed Move Added",0,0,255
560,"Invalid Midpoint",255,0,0
561,"Arc Mid-Point Added",0,0,255
562,"Invalid End-Point",255,0,0
563,"Arc End-Point Added",0,0,255
564,"Exited Manual Digitizer",0,0,255
565,"Pausing...",0,0,255
566,"Continuing...",0,0,255
567,"Pausing Signal On...",0,0,255
568,"Continuing Signal On...",0,0,255
569,"Pausing... - ",0,0,255
570,"Continue Disabled Signal On",255,0,0
571,"DA Device Initialization Failed",255,0,0
572,"Minimum of 3 ARCFEED lines required. Using Auto Mode.",255,0,0