× Phone: (304) 472-7206 Contact: Information Page Assist: TeamViewer
Home
WinCNC SOFTWARE

Description
PC Requirements
Demo
Purchase
Support/Training
WinCNC Manual

CNC MACHINE TYPES

Routing
Plasma Cutting
Knife Cutting
Laser Cut/Engrave
Vision Registration
2D/3D Digitizing
Other Applications

Hardware and Parts

The prices shown are for our PC hardware and CNC parts. Price discounts are available for quantity purchases and resellers. Please e-mail sales@wincnc.net for more information.

Note: These are supplemental and replacement hardware parts and DO NOT include any software licensing required to run WinCNC. Prices subject to change without notice.

PCI Card - $300.00
For replacement of the PCI7200 card. When ordering specify the revision number of the old or damaged PCI7200 card.
PCIe Card - $350.00
For replacement of the PCIe7200 card. The PCI Express card is only compatible with WinCNC 2.6 and WinCNC 3.0, and can not be used with older versions of WinCNC.
37 Pin Daughter Board - $110.00
For replacement of the WinCNC Daughter Board. This is the standard WinCNC connector used on the majority of OEM equipment running WinCNC. When ordering specify the revision number on the old/damaged daughterboard. Can only be purchased with a WinCNC software license or with the return of the original daughter board for software license transfer.
37 & 25 Pin Daughter Board - $110.00
For replacement of the WinCNC Daughter Board. This is a non-standard LPT port configuration used on some OEM equipment running WinCNC. When ordering specify the revision number on the old/damaged daughterboard. Can only be purchased with a WinCNC software license or with the return of the original daughter board for software license transfer.
Dual 25 Pin Daughter Board - $110.00
For replacement of the WinCNC Daughter Board. These jumper configurable LPT port configurations are used on some OEM equipment and CNC machines converted to WinCNC from other LPT port controllers. When ordering specify the revision number on the old/damaged daughterboard. Can only be purchased with a WinCNC software license or with the return of the original daughter board for software license transfer.
WinCNC CN2 IO Board - $300.00
Interface board w/screw terminals for CN2. Features: 4 high voltage relays, 14 opto isolated inputs, 6 motor connections, a/c input, emergency switch, and 5v & ground output terminals for external uses. Comes with 10 ft 37 pin shielded cables for Daughter Board connector.
WinCNC CN1/CN2 Interface Board - $500.00
Interface board w/screw terminals for CN1 and CN2. Features: 12 high voltage relays, 8 logical outputs, 30 opto isolated inputs, 6 motor connections, a/c input, emergency switch, 5v & ground output terminals for external uses. Comes with 2 ft 37 pin ribbon cables for PCI card and Daughter Board connectors.
8 Channel Input Isolation Board - $80.00
8 channel input isolation board with removable screw terminals and on-board 24VDC power supply. Features: Provides eight (8) fully isolated input channels. DIN rail mount included. 110~220 VAC input. Can be connected to any available input pin on CN1 and/or CN2. Can be used with any 24V compatible contact switches and signals.
4 Relay Module Adapter Board - $50.00
Screw terminal module with 4 AC/DC relays. 5VDC wall outlet adapter included for required 5VDC input.
Tower PC - $590.00
Upgrades and customization available on request. The basic PC configuration is Windows 10 Home 64bit (+$40 for Windows 10 Pro), Pentium 3.7Ghz CPU, 8GB DDR4 RAM, 500GB SSD, CD/DVD RW, Wired LAN, Front/Rear Audio, Front/Rear USB and HDMI/DVI/VGA video output. Tower case dimensions are 16.25D x 7.25W x 14.25H.
Desktop PC - $610.00
Upgrades and customization available on request. The basic PC configuration is Windows 10 Home 64bit (+$40 for Windows 10 Pro), Pentium 3.7Ghz CPU, 8GB DDR4 RAM, 500GB SSD, CD/DVD RW, Wired LAN, Front/Rear Audio, Front/Rear USB and HDMI/DVI/VGA video output. Desktop case dimensions are 12D x 5.5W x 12.5H.
ITX PC - $630.00
Upgrades and customization available on request. The basic PC configuration is Windows 10 Home 64bit (+$40 for Windows 10 Pro), Pentium 3.7Ghz CPU, 8GB DDR4 RAM, 500GB SSD, CD/DVD RW, Wired LAN, Built-in WiFi, Front/Rear Audio, Front/Rear USB and HDMI/DVI/VGA video output. ITX case dimensions are 11.22D x 8.74W x 7.13H.
Computer Monitor - $120.00
19 inch LCD Monitor with VGA and DVI input.
Wired USB Keyboard and Mouse - $30.00
Microsoft wired USB keyboard and optical mouse.
AC Stepper Drive - $229.00
8 AMP stepper motor driver with 110/120 VAC input. 220 VAC model available. Features switch configurable amperage, automatic anti-resonance tuning, switch configurable micro-stepping, and digital DSP technology for quiet and smooth motor operation.
DC Stepper Drive - $139.00
6 AMP stepper motor driver with 24-80 VDC input. Features switch configurable amperage, switch configurable micro-stepping, and digital DSP technology for quiet and smooth motor operation.
60 VDC Power Supply - $119.00
8.5A 60VDC Power Supply with 110/220 VAC input. Powers 1-3 DC Stepper Drives.
MX3660 3 Axis Stepper Drive - $299.00
6 AMP stepper motor driver with 48 VDC input. Features switch configurable amperage, switch configurable micro-stepping, and digital DSP technology for quiet and smooth motor operation. Includes general purpose inputs, outputs, and analog spindle speed.
MX4660 4 Axis Stepper Drive - $399.00
6 AMP stepper motor driver with 48 VDC input. Features switch configurable amperage, switch configurable micro-stepping, and digital DSP technology for quiet and smooth motor operation. Includes general purpose inputs, outputs, and analog spindle speed.
48 VDC Power Supply - $109.00
10.4A 48VDC Power Supply with 110/220 VAC input. Powers MX3660 or MX4660 DC Stepper Drives.
368 oz/in stepper motor - $49.00
NEMA 23, 1/4 inch single flat shaft, 4 wire stepper motor. Features 368 oz/in holding torque, smooth motion, low heating, and quiet operation.
640 oz/in stepper motor - $129.00
NEMA 34, 1/2 inch keyed shaft, 4 wire stepper motor. Features 640 oz/in holding torque, smooth motion, low heating, and quiet operation.
1280 oz/in stepper motor - $159.00
NEMA 34 double stack, 1/2 inch keyed shaft, 4 wire stepper motor. Features 1280 oz/in holding torque, smooth motion, low heating, and quiet operation.
GCNC-CN2 Stepper Enclosure - $2,150.00

Requires a 37 Pin Daughter Board.

Enclosure contains:
  • CN2 IO board
    • 120VAC to 240VAC single phase power.
    • Two banks of 7 digital inputs. Each bank can be set to handle 5VDC, 12VDC, or 24VDC.
    • Four mechanical NC/NO output relays - Max 10A at 28VDC, 12A at 125VAC, 10A at 277VAC.
    • Available spindle speed control when enabled through WinCNC.
    • E-Stop.
  • 4 2-6 Amp digital stepper drives (7 Amp peak).
  • 2 60VDC 8Amp 120/240VAC power supplies.
1 DIN Rail mounted 24VDC low current power supply for limit switches and other inputs. Externally controlled On/Off switch. 19 3/4 in x 23 5/8 in.

GCNC-MX Stepper Enclosure - $1,600.00

Requires a Dual 25 Pin Daughter Board.

Enclosure contains:

4-axis digital stepper drive
  • 4 integrated 1-4.25 Amp stepper drives (6 Amp peak).
  • 8 opto-isolated digital inputs.
  • 4 outputs.
  • Onboard E-Stop.
1 DIN Rail mounted 24VDC low current power supply for limit switches and other inputs. 1 48VDC 120VAC/240VAC power supply. 25 pin connector to receive and send signal to WinCNC. All IO available on screw terminals at the outside of the enclosure. Externally controlled On/Off switch. 14 in x 17 3/4 in.

Tool Measure Switch - $200.00
Used, with or without an automatic tool changer, to zero bits to the table or material surface automatically or at the click of a button.
Adapter Box 3-DB25 - $150.00
Custom wiring adpater for LPT port CNC machine conversions and upgrades using 1-3 DB25 connectors.
Adapter Box 20/50 pin header - $300.00
Custom wiring adpater for ribbon cable header CNC machine conversions and upgrades using 20, 40, and 50 pin connectors.
DB37 10ft M/F Cable - $15.00
10ft DB37 male to female extension cable. Use to connect the CN1 or CN2 connector of the WinCNC hardware to an IO board, breakout board, or other compatible CNC drive system.
DB37 Breakout - $65.00
Passive screw-terminal IO breakout board. Several solder through-holes for each IO pin allow installation of components such as resitors or LEDs.
Handheld Serial Keypad - $500.00
This is used to control WinCNC away from the PC using the included 15ft cable. Additional purchase of software support is required to use the Serial Keypad with WinCNC.
Handheld Wireless Keypad - $400.00
This is used to control WinCNC away from the PC up to 300ft. Additional purchase of software support is required to use the Wireless Keypad with WinCNC. Requires WinCNC 2.6 or newer.
Raw Arc Voltage Monitor Board - $300.00
Used with the THC software feature to monitor raw arc voltage from a plasma cutter.
THC IO Board - $400.00
Used with the THC software feature to montior divided arc voltage from a plasma cutter using an arc voltage divider. Also includes two output relays and 4 5/12/24VDC inputs. All IO is completely optically isolated from the plasma unit for maximum noise immunity and electrical protection. Requires WinCNC 2.6 or newer.
Arc Voltage Divider - $160.00
Used to divide raw arc voltage 40:1. If a plasma cutter does not have a built-in voltage divider then this would be required for using the Divided Arc Voltage Montior IO Board.